Watch the video * Watch the video *
Localized electromagnetic interference or building materials (such as steel framing or concrete walls) are blocking the radio waves. Solution: Move the clock to a window sill facing Colorado.
The back of your Kincaid clock features several control buttons. Here is a directory of what they do:
If your Kincaid shows the wrong time after three nights:
Q: Can I use my Kincaid radio controlled clock in different time zones? A: Yes, you can set the clock to display the time in different time zones. Refer to the instruction manual for specific instructions on how to set the time zone.
Press and hold the button for 3–5 seconds until the digital display digits begin to flash (or the setup mode activates).
Before inserting batteries, choose a temporary setup location. Place the clock near a window facing Colorado (for North American users) to ensure the strongest possible line-of-sight to the WWVB transmitter. Avoid placing it near heavy electronics, routers, or microwave ovens during this phase. Step 2: Insert the Batteries
If your Kincaid clock has a on the back:
Once the pin is removed, open the battery compartment. Kincaid clocks are powered by one fresh . Always use a new, high-quality battery, as a weak battery is a very common cause of reception problems. Ensure it's inserted according to the + and - polarity marks shown inside the compartment.
This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.
: If the clock doesn't set after 12 minutes, move it to a different location away from electronics like TVs or computers, which can cause interference.
Press to confirm your selection and advance to the next setting. The standard programming sequence for Kincaid clocks is:
Always orient the front or back of the clock facing toward Fort Collins, Colorado, as the internal antenna is directional. Section 6: Maintenance and Care
: Place the clock near a west-facing window overnight. It can take 3 to 12 minutes—or up to 24 hours in some conditions—to catch the signal and set the correct time. Troubleshooting Common Issues
: Place a fresh AA alkaline battery into the compartment.
Localized electromagnetic interference or building materials (such as steel framing or concrete walls) are blocking the radio waves. Solution: Move the clock to a window sill facing Colorado.
The back of your Kincaid clock features several control buttons. Here is a directory of what they do:
If your Kincaid shows the wrong time after three nights:
Q: Can I use my Kincaid radio controlled clock in different time zones? A: Yes, you can set the clock to display the time in different time zones. Refer to the instruction manual for specific instructions on how to set the time zone.
Press and hold the button for 3–5 seconds until the digital display digits begin to flash (or the setup mode activates).
Before inserting batteries, choose a temporary setup location. Place the clock near a window facing Colorado (for North American users) to ensure the strongest possible line-of-sight to the WWVB transmitter. Avoid placing it near heavy electronics, routers, or microwave ovens during this phase. Step 2: Insert the Batteries
If your Kincaid clock has a on the back:
Once the pin is removed, open the battery compartment. Kincaid clocks are powered by one fresh . Always use a new, high-quality battery, as a weak battery is a very common cause of reception problems. Ensure it's inserted according to the + and - polarity marks shown inside the compartment.
This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.
: If the clock doesn't set after 12 minutes, move it to a different location away from electronics like TVs or computers, which can cause interference.
Press to confirm your selection and advance to the next setting. The standard programming sequence for Kincaid clocks is:
Always orient the front or back of the clock facing toward Fort Collins, Colorado, as the internal antenna is directional. Section 6: Maintenance and Care
: Place the clock near a west-facing window overnight. It can take 3 to 12 minutes—or up to 24 hours in some conditions—to catch the signal and set the correct time. Troubleshooting Common Issues
: Place a fresh AA alkaline battery into the compartment.